TAIG ACCESSORIES !
E-MAIL US..... OR CALL.... (806) 381-8898
SELECT FROM OUR HUGE INVENTORY!
WE CARRY EVERY ACCESSORY FOR ANY TAIG MACHINE !
BUY THEM RIGHT HERE.... RIGHT NOW WITH OUR SECURE SHOPPING CART !
We Maintain A full Stock Of Taig Accessories.
|
ER Fly Cutter.... This great little tool does the same job as the screw on fly cutter. The difference is, this slides right into a 3/8 collet. Works with any 3/8 collet!! On Any Machine!
Great tool for surfacing off material. Comes complete, as shown. Your Cost Only.... $19.75
|
ER Drill chuck arbor adapter. This Adapter makes it possible to attach drill chucks w/ 3/8- 24 thread and other tooling to the new style ER spindles that Taig now offers. Works with any 3/8 collet. Get Yours Today! Requires 3/8 Collet not included...see our ER collet selection and great prices! Retail Price... $14.95 .....Your Cost Only....$12.85
|
| Marathon Motor 115v 60 HZ 1725 RPM 1/4 HP,
1/2" shaft pre-wired with switch and ready to go. Stock # 1021W Your Cost Only..... $119.50 |
Motor mount bracket with
necessary hardware,
fits the above motor and nema 48 frame motors. Cheaper Than You Can Make It! Stock # 1022 Only...$5.19 |
| NICE! Mounting Base 12" x
18" used for No. 1021 motor. This is the base plate only, motor mount bracket not included.Stock # 1023 Only...$7.59 |
 Depth Stop
for workpiece in chuck
|
 4
jaw.... 3 1/4" dia. chuck 3/4-16 thread for mounting. The jaws
adjust independently. Reversible heat treated steel jaws. NICE!Stock # 1030 Retail $64.75....Only...$63.99 |
 Lathe Dog for holding work piece
while turning between centers. Stock # 1034 Only...$9.35 |
 Face plate 3
1/4" dia. 3/4-16 thread for mounting.Stock # 1035 Only...$14.75
|
 Face
plate for wood turners. Screws onto the lathe spindle nose.
Stock # 1037-3H Only....$10.79 |
3-1/4" Face
Plate angle bracket set. Stock # 1036
Only...$5.69 |
 Tool
Rest...4" Swivel joint, adjustable HeightFor Wood Turners! NICE! Stock # 1038
Only...$26.50 |
 Collet Set, 7 collet sizes that
will work with the Taig mills or lathe. The sizes are: 1/8,5/32,3/16,7/32,1/4,9/32,5/16. Stock # 1040.
Only...$32.50
|
 Collet
Closer (Spindle Nut) Fits both The Taig Mill & Lathe.Stock # 1042 Only...$5.69
|
 Set of 4 blank collets for making
special arbors.Can be bored and slotted. Stock # 1043 Only...$2.69
|
 3 Jaw Chuck 3-1/4" Diameter with
3/4-16 mounting threads. Self centering, steel body, comes with reversible aluminum soft jaws. Stock # 1050 Retail... $64.10 Only...$63.89 |
 Blank
soft jaw set.... Cut into these to match any special holding
needs.
Keep an extra set on hand! Stock # 1051 Only...$8.75 |
 Full Circle soft jaw set.... Works
Great!Stock # 1052 Only...$7.69
|
 4 Jaw SELF CENTERING scroll Chuck.
3-1/4" Dia. 3/4-16 threaded mount,
Steel Body with reversible aluminum soft jaws.
Stock # 1060 Retail... $72.40 Only...$71.99 |
 0 to 1/4" Jacobs drill chuck,
industrial quality.3/8-24 thread to fit drill arbor. Stock # 1090 Only...$36.95
|
 0 to 1/4" Jacobs drill chuck,
Commercial quality.3/8-24 thread to fit drill arbor. Stock # 1091 Only...$10.19
|
 1/16 to 3/8"
Jacobs drill chuck, commercial quality.
3/8-24 thread to fit drill arbor.
Stock # 1092 Only...$10.19 |
 1/8" to 1/2" Jacobs drill chuck,
Commercial quality.3/8-24 thread to fit drill arbor. Stock #1093 Only...$18.50
|
 Slitting Saw Arbor! Screws directly
onto lathe spindle. (Blade Not Included)Wrench included. Stock # 1110 Only...$5.49 |
|
High speed steel slitting saw
blade. .032" x 2-1/2" diameter for arbor above...(Arbor Not Included) Stock # 1111 Only...$12.59 |
 Grinding Wheel Arbor...NICE!Screws directly onto lathe spindle. Stock # 1120 Only...$6.19 |
 Grinding Wheel Set...Fits Arbor Above.... Stock # 1122
|
 Drill Chuck Arbor for Jacobs chucks
above. Attaches Chucks
to spindle 3/8-24 thread.Stock # 1140
|
 Drilling Tailstock. Lever operated
with 5/8" offset with dead center. 3/8-24 thread. Stock # 1150 |
 Needle bearing center. Spring
Loaded! Nice!
Stock # 1151 |
 This Die Holder fits in the
tailstock. Holds
13/16" & 1" Button Dies. Great for threading!
Stock # 1152 |
Gates "V" Belt # 3M 315 12-1/2"
Flat Length. Stock # 1159 Only...$7.89 |
| Gates "V" Belt # 3M 500 20" Flat
Length.
Stock # 1160 Only...$7.89 |
 Six Step Pulley Set...2 per set
3/8" bore 3M 500 BeltIncluded. Stock # 1161 Only...$25.49 |
| Six Step Pulley Set...2 per set
1/2" bore 3M 315 Belt Included. Stock # 1162 Only...$25.49 |
 Tool Post for Taig lathe...
Holds lathe cutting tools during cutting operations.
Stock # 1170 Only...$4.50 |
 Back Tool Post. The tool mounts
upside down and two tools can be used at once in this holder. Stock # 1171 Only...$4.99
|
 T-Bar cut off tool.... Height Adjustable!
Stock # 1173
Only...$29.99 |
 3-Point Steady Rest! NICE! 3/32" to
1-1/2" Capacity.
Stock # 1190 Only...$24.99 |
 This Top Slide makes your slide
compound. Mounts on the
cross slide. Great for cutting tapers and angles!
Stock # 1200 Only...$44.50 |
 Radius Turner! Allows you to turn
ball ends on shafts. Swings tool in an arc. Great!
Stock # 1210 Only...$19.99 |
 Milling Attachment... makes your
lathe work like a mill!
Great attachment! Mounts directly on cross slide! 2" X 3-3/4"
table.
Stock # 1220 Only...$62.75 |
 Chuck Adapter. Adapts 3/4-16
threaded chuck to mill table.
Stock # 1221 Only...$14.39 |
 Fly Cutter. 1-1/4" to 2-1/2" diameter. 3/4-16 thread mount. Tool bit is included!
Stock # 1224
Only...$19.75 |
 Milling Vise with thumb screw.
Opening is 2-1/8" X 2" wide.Makes holding stock very easy. Stock # 1225
Only...$27.50 |
Riser block kit for headstock and tool post.
Allows a 6" swing. (photo on right for clarification only)
Stock # 1250 Only...$24.95 |
 Tail Stock Riser... Matches Head
Stock riser above.
Stock # 1251 Only...$20.89 |
Complete Head Stock With ER 16 Spindle!
Only.... $113.99
|
| FITS
TAIG SPINDLE & COLLET CLOSER ! NOW AVAILABLE FOR THE -ER- SPINDLE! It takes both of these wrenches to do the job! Comfortable & safe! No more bruised and cut knuckles from slipping wrenches!
Made By "CLASS" # 4409 SpindleWrenchSet ...OR... #4409 ER Spindle Wrench Set
IN STOCK . READY TO SHIP ! ONLY .... $ 36.95 ! SAVE! Buy Now! Select 4409 or 4409ER Below |
We Carry American Made Micro Grain Carbide Cutting Tools. See Our End Mill Selection!
Our Shopping Cart is Secure & Safe! |
| View Shopping Cart Contents | |
Now you can use 3/8" shank tools in your mill. Check out our
Ultra Precision ER Collets!
Tooling & Work Holding